Ensure all pneumatic connections are hand-tightened to prevent ambient air leaks. 3. Operating Instructions
The central unit housing the display, processor, and control interface.
Note: For specific wiring diagrams or internal circuit repairs, always consult an authorized service center to maintain the device's certification.
| Error Code | Meaning | Fix from Manual | |------------|---------|----------------| | | Sensor missing | Replace sensor module | | E-002 | Sensor weak / expired | Calibrate or replace | | E-003 | Low battery (<10%) | Charge immediately | | E-004 | Pump failure (if equipped) | Clean pump filter | | E-005 | Zero drift too high | Re-zero in fresh air | | F-001 | Flash memory error | Factory reset (contact support) |
: If operating the unit inside a vehicle cabin during mobile diagnostic evaluations, maintain continuous fresh airflow to prevent hazardous carbon monoxide gas saturation.
| Specification | Detail | |---|---| | | Mains: 90–270 V, 50–60 Hz; Battery: 11–16 Volt (5A F fuse) | | Maximum Power | 70 W | | Display | Color graphic LCD, 320 × 240 resolution | | Keyboard | 11 base keys + 5 silicone rubber function keys with special surface treatment | | Memory Card Slot | PCMCIA (up to 64 Mbyte) | | Printer | 24-column thermal printer (workshop address printable) | | Serial Outputs | COM1, COM2 (for autodiagnosis interface and smokemeter connection) | | Other Ports | RS232/PC serial for OP/diagnostic stations connection; RS485 industrial serial; Parallel printer output for 80-column standard printer (color capable); miniDIN 6-way for electronic key activation | | VGA Output | For external monitor connection | | Measured Gases | O2, CO, CO2, HC, NOx |
: Available on Scribd - STARGAS 898 User Manual .
To maintain regulatory compliance, the gas bench must be calibrated using certified calibration gas bottles (
Ensure all pneumatic connections are hand-tightened to prevent ambient air leaks. 3. Operating Instructions
The central unit housing the display, processor, and control interface.
Note: For specific wiring diagrams or internal circuit repairs, always consult an authorized service center to maintain the device's certification. stargas 898 user manual
| Error Code | Meaning | Fix from Manual | |------------|---------|----------------| | | Sensor missing | Replace sensor module | | E-002 | Sensor weak / expired | Calibrate or replace | | E-003 | Low battery (<10%) | Charge immediately | | E-004 | Pump failure (if equipped) | Clean pump filter | | E-005 | Zero drift too high | Re-zero in fresh air | | F-001 | Flash memory error | Factory reset (contact support) |
: If operating the unit inside a vehicle cabin during mobile diagnostic evaluations, maintain continuous fresh airflow to prevent hazardous carbon monoxide gas saturation. Note: For specific wiring diagrams or internal circuit
| Specification | Detail | |---|---| | | Mains: 90–270 V, 50–60 Hz; Battery: 11–16 Volt (5A F fuse) | | Maximum Power | 70 W | | Display | Color graphic LCD, 320 × 240 resolution | | Keyboard | 11 base keys + 5 silicone rubber function keys with special surface treatment | | Memory Card Slot | PCMCIA (up to 64 Mbyte) | | Printer | 24-column thermal printer (workshop address printable) | | Serial Outputs | COM1, COM2 (for autodiagnosis interface and smokemeter connection) | | Other Ports | RS232/PC serial for OP/diagnostic stations connection; RS485 industrial serial; Parallel printer output for 80-column standard printer (color capable); miniDIN 6-way for electronic key activation | | VGA Output | For external monitor connection | | Measured Gases | O2, CO, CO2, HC, NOx |
: Available on Scribd - STARGAS 898 User Manual . To maintain regulatory compliance, the gas bench must
To maintain regulatory compliance, the gas bench must be calibrated using certified calibration gas bottles (